Dental radiation safety: OSHA rules, state programs and badges

Last reviewed November 18, 2026  ·  11 sources

Short answer

Dental radiation safety rules come from two places. OSHA's ionizing radiation standard, 29 CFR 1910.1096, limits a worker's whole body dose to 1¼ rems per calendar quarter, requires a dosimeter badge only when someone is likely to get more than 25 percent of that limit, and requires staff in a radiation area to be told about its hazards and precautions. Your state's radiation control program registers and inspects the x-ray machines, and in the 23 states named in the OSHA standard the state's rules govern instead.

The ADA no longer recommends lead aprons or thyroid collars for patients (2024), and the FDA and ADA recommend rectangular collimation and staying behind a barrier. The free one-page checklist below covers each item.

Who sets the dental radiation safety rules

Rule makerWhat it coversLegal status
OSHA, 29 CFR 1910.1096Worker dose limits, badges, signs, instruction, exposure recordsLaw, except where a state named in 1910.1096(p)(3) governs
Your state radiation control programMachine registration and inspection; depending on the state, operator rules, shielding and postingLaw in that state
FDA, 21 CFR 1020.30 and 1020.31How x-ray machines must perform when made and installedLaw for manufacturers and installers
FDA and ADA recommendations; ADA expert panels (2024, 2026)Technique, patient selection, shielding, badgesRecommendations

OSHA notes that "most states have a radiation control agency responsible for regulating radiation-producing machines," and that OSHA State Plans, such as Cal/OSHA, "may have more stringent requirements for occupational exposures to ionizing radiation."

States where the state's rules govern

Under 1910.1096(p)(3), an employer that has registered its radiation sources with one of these states and follows the state's laws and regulations is treated as meeting the OSHA standard: Alabama, Arizona, Arkansas, California, Colorado, Florida, Georgia, Idaho, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Nebraska, New Hampshire, New York, North Carolina, North Dakota, Oregon, South Carolina, Tennessee, Texas and Washington. In those states the state's rules also govern staff instruction (1910.1096(i)(1)).

Your state radiation control program

Every state sets its own x-ray rules, so this page does not list them. Find your state's program on the CRCPD map of state radiation control programs and check:

  • how and when you register each x-ray unit, including hand-held units and cone-beam CT,
  • how often the state inspects, and what you must keep for the inspector,
  • who may take x-rays in your state, and which certificate or permit each person needs,
  • any rules on shielding, posting and personnel monitoring.

OSHA dose limits

OSHA limits the dose a worker in a restricted area may receive in one calendar quarter (1910.1096(b)(1), Table G-18):

Part of the bodyLimit per calendar quarter
Whole body: head and trunk, active blood-forming organs, lens of the eyes, or gonads1¼ rems
Hands and forearms, feet and ankles18¾ rems
Skin of the whole body7½ rems

A higher whole body dose is allowed only under the conditions in 1910.1096(b)(2), with exposure records that prove the worker stays within its formula. An employee under 18 may receive no more than 10 percent of these limits (1910.1096(b)(3)).

Radiation badges for dental offices

What OSHA requires. The employer supplies a badge or other personnel monitoring device, and requires its use, for (1910.1096(d)(2)):

  1. each employee who enters a restricted area and receives, or is likely to receive, more than 25 percent of the quarterly limit in a calendar quarter (for the whole body, 25 percent of 1¼ rems is 0.3125 rem),
  2. each employee under 18 who is likely to receive more than 5 percent of the limit, and
  3. each employee who enters a high radiation area.

What the FDA and ADA recommend. "Personal dosimeters should be used by workers who may receive an annual dose greater than 1 mSv," and "pregnant dental personnel operating x-ray equipment should use personal dosimeters." These are recommendations, not OSHA rules.

In practice. The machine survey, or your state program, tells you whether staff are likely to cross OSHA's line. An office that is not required to use badges can still choose them. If staff wear badges, the readings are exposure records: OSHA's records access rule covers them and requires them to be kept at least 30 years (29 CFR 1910.1020(d)(1)(ii)), and each badged employee is told their own exposure at least once a year (1910.1096(n)(1)).

Caution signs and posting

OSHA defines a radiation area as one where a major part of the body could receive more than 5 millirem in 1 hour, or more than 100 millirem in 5 consecutive days (1910.1096(d)(3)(ii)). Each radiation area must be posted with the radiation symbol and the words "CAUTION RADIATION AREA" (1910.1096(e)(2)). Whether any spot in your office meets that definition is a question the machine survey answers. Your state may have its own posting rules.

OSHA also requires you to post a copy of the standard and your operating procedures where staff will see them, or keep them available on request (1910.1096(i)(3)).

Dental radiography safety training

OSHA requires that everyone working in or often entering a radiation area be (1910.1096(i)(2)):

  • told about the radiation in that area,
  • taught the safety problems of the exposure and the precautions or devices that reduce it,
  • taught the parts of the standard that protect them, and
  • told about the exposure reports they can request.

The standard sets no yearly retraining interval and no retention period for the training record. In the states named in 1910.1096(p)(3), the state's rules govern instruction. Training the team every year with your other OSHA courses, and keeping the record for 3 years, is office practice. The other yearly topics are in OSHA training for dental offices.

Dental x-ray safety for the person taking the image

The FDA and ADA recommendations (revised 2012, still on the FDA site) say:

  • Stand behind a barrier when possible. Barriers should ideally "contain a leaded glass window to enable the operator to view the patient during exposure."
  • If there is no barrier, "the operator should stand at least two meters from the tube head and out of the path of the primary beam."
  • "Dental professionals should not hold the receptor holder during exposure."
  • Use "the fastest image receptor compatible with the diagnostic task (F-speed film or digital)."
  • Use rectangular collimation for periapical and bitewing images. "A rectangular collimator decreases the radiation dose by up to fivefold as compared with a circular one."
  • Hand-held units: if the ring shield is not in place, the operator wears a lead apron. When no authorized user is supervising them, keep the units in "locked cabinets, locked storage rooms, or locked work areas."
  • "A qualified expert should survey all x-ray units on their placement and should resurvey the equipment every four years," or after changes that may affect exposure. Your state may set its own schedule.

Dental radiology safety for patients: what the ADA says now

  • Aprons and thyroid collars. In February 2024 an ADA expert panel said lead aprons and thyroid collars "are not necessary to shield patients from radiation exposure," and that this applies to all patients, "regardless of age or health status (like pregnancy)." They can block the primary beam and cause retakes. The 2012 FDA and ADA recommendations on the FDA site still advise thyroid collars, so the newer ADA panel and the older FDA page differ. If your state rule requires patient shielding, follow your state.
  • Beam size and receptors. The 2024 recommendations call for digital imaging instead of film and restricting the beam to the area being assessed ("rectangular collimation").
  • Ordering images. In January 2026 the ADA published patient selection recommendations, endorsed by the American Academy of Oral and Maxillofacial Radiology, that say dental x-rays "should be ordered only when clinically necessary." They also cover cone-beam CT.

Pregnant staff

  • OSHA: 1910.1096 has no separate dose limit for pregnancy.
  • NRC: for NRC licensees, the dose to the embryo or fetus of a declared pregnant worker must not exceed 0.5 rem (5 mSv) during the whole pregnancy (10 CFR 20.1208). Declaring is voluntary and done in writing. Dental x-ray machines are regulated by states, not the NRC. OSHA notes that the CRCPD's suggested state regulations recommend the same 500 mrem limit, so your state may have a matching rule.
  • ADA: if a pregnant employee may take radiographs, provide a personal dosimetry badge and barrier protection; if shielding is not possible, she stands at least two meters from the tube head and out of the primary beam. The ADA also suggests a written radiation safety policy in the employee handbook and checking your state program for added requirements.

She decides with her physician whether she needs an accommodation. Keep any declaration private.

Free dental radiation safety checklist

One page. Each line is tagged OSHA (with the paragraph of 1910.1096), State, FDA/ADA or ADA. Go through it once a year, when you add or move an x-ray unit, and when someone new starts taking x-rays.

Dental radiation safety checklist

complyday.com
Office:State:Radiation safety contact:Date:

Program and state rules

  • A radiation safety contact is named for the officeOffice
  • Each x-ray unit (including hand-held and CBCT) registered with the state programState
  • State inspection and survey reports filed; next due date knownState; FDA/ADA
  • Each person who takes x-rays is allowed to by the state, with any required permitState

Staff training and posting

  • Staff in radiation areas told of the hazards, precautions and their rightsOSHA (i)(2)
  • Copy of the standard and operating procedures posted or availableOSHA (i)(3)
  • Any radiation area posted "CAUTION RADIATION AREA" with the symbolOSHA (e)(2)

Dose and badges

  • Badges worn where a worker is likely to get over 25% of the quarterly limitOSHA (d)(2)
  • Workers under 18: badge over 5%, dose no more than 10% of the limitsOSHA (b)(3), (d)(2)
  • Badges considered for anyone who may receive over 1 mSv a yearFDA/ADA
  • Pregnant staff who take x-rays offered a badgeFDA/ADA; ADA
  • Badged staff told their own exposure at least once a yearOSHA (n)(1)
  • Badge readings kept at least 30 years1910.1020(d)(1)(ii)

Technique and equipment

  • Operator behind a barrier, or 2 meters from the tube head and out of the beamFDA/ADA
  • Staff never hold the receptor holder during exposureFDA/ADA
  • Rectangular collimation for periapical and bitewing imagesFDA/ADA; ADA
  • Digital receptors or F-speed filmFDA/ADA; ADA
  • Units surveyed at installation and every four years or after changesFDA/ADA; State
  • Hand-held units locked away when unsupervised; ring shield in placeFDA/ADA
  • Patient shielding follows your state rule (ADA no longer recommends it)State; ADA

OSHA = 29 CFR 1910.1096. In Alabama, Arizona, Arkansas, California, Colorado, Florida, Georgia, Idaho, Kansas, Kentucky, Louisiana, Maryland, Mississippi, Nebraska, New Hampshire, New York, North Carolina, North Dakota, Oregon, South Carolina, Tennessee, Texas and Washington, the state's rules govern (1910.1096(p)(3)). State = your state radiation control program: add its items. FDA/ADA = 2012 recommendations. ADA = 2024 expert panel and ADA employer guidance. Office = office practice.

Open the printable dental radiation safety checklist or use the download button.

Keep it with your other OSHA records

Radiation safety sits beside the bloodborne pathogens and chemical rules in OSHA requirements for dental offices. If you still develop film, the developer and fixer belong in your chemical training: see hazard communication training. The full yearly list is the dental OSHA compliance checklist.

The free way is this checklist, your state program's rules and a binder. ComplyDay is the faster way: a radiation safety course is one of six yearly courses (seven in California) on staff phones, each person's x-ray permit is kept with its expiry date and an email reminder, and the records go into your inspection binder.

Questions

Does OSHA require dosimeter badges in a dental office?

Only for an employee who enters a restricted area and is likely to receive more than 25 percent of OSHA’s quarterly limit in a calendar quarter (5 percent for an employee under 18), or who enters a high radiation area (29 CFR 1910.1096(d)(2)). In the 23 states named in 1910.1096(p)(3), the state’s rules govern instead. The FDA and ADA recommend badges for workers who may receive more than 1 mSv a year and for pregnant staff who operate x-ray equipment, whatever the expected dose.

Do dental patients still need a lead apron and thyroid collar?

The ADA no longer recommends them. Its expert panel said in February 2024 that lead aprons and thyroid collars “are not necessary to shield patients from radiation exposure,” for all patients, including pregnant patients. The older FDA and ADA recommendations from 2012, still on the FDA site, say thyroid collars should be used whenever possible. These are recommendations. If your state rule requires shielding, follow your state.

Is dental x-ray safety training required every year?

OSHA requires that everyone working in or often entering a radiation area be told about the radiation, its hazards and the precautions, and the parts of the standard that protect them (1910.1096(i)(2)). It sets no yearly interval. In the states named in 1910.1096(p)(3) the state’s rules govern instruction. Yearly training is office practice unless your state requires more.

Can a pregnant dental assistant take x-rays?

No federal rule bars it. The ADA recommends giving a pregnant employee who may take radiographs a personal dosimetry badge and barrier protection, and having her stand at least two meters from the tube head and out of the beam when there is no barrier. The 0.5 rem (5 mSv) limit for a declared pregnant worker is an NRC rule, and the suggested state regulations include the same limit, so check your state program. She decides with her physician whether she needs an accommodation.

Who inspects dental x-ray machines?

Your state’s radiation control program. OSHA notes that most states have a radiation control agency responsible for regulating radiation-producing machines. Depending on the state, the program registers the machines, inspects them and sets rules on operators. The FDA and ADA also recommend that a qualified expert survey each unit when it is installed and every four years.

Sources

  1. eCFR: 29 CFR 1910.1096, Ionizing radiation
  2. eCFR: 29 CFR 1910.1020, Access to employee exposure and medical records
  3. eCFR: 21 CFR 1020.30, Diagnostic x-ray systems and their major components (FDA)
  4. OSHA: Ionizing radiation, standards
  5. OSHA: Ionizing radiation, pregnant workers
  6. eCFR: 10 CFR 20.1208, Dose equivalent to an embryo/fetus (NRC)
  7. FDA: The Selection of Patients for Dental Radiographic Examinations (FDA and ADA recommendations, revised 2012)
  8. ADA: Updated recommendations to enhance radiography safety in dentistry (February 1, 2024)
  9. ADA: New recommendations confirm dental x-rays most effectively used in moderation (January 5, 2026)
  10. ADA: Radiation safety for pregnant dental staff and patients
  11. CRCPD: Radiation control programs and directors (map of state programs)